| | |
RCU-02 Ref: 104-102
The RCU-02 is a radio remote controlled switching unit that will allow the remote operation of any appropriate electrical appliance that is required. The unit is constructed to commercial standards, giving the convenience of remote operation and in most cases the reduction in installation costs will exceed the cost of switching unit. Supply voltage range from 10-24V ac or dc. Antenna is on the end of a 1m lead for remote fixing at a higher level Dimensions (WxHxD): 75x27x50mm Delivery A SPECIAL OFFER WAS £35.50 NOW ONLY £10 whilst stocks last
Instruction sheet (PDF)
Price: £10.00 (Excluding: VAT at 17.5%) |  |
|
|
 | DIN Rail Telemetry Qmax Range Ref: 104-114
This is a flexible Radio Remote control system which may be constructed by simply plugging together the desired modules. The transmitters are supplied as either a hand held fob or DIN Rail mounting Telemetry Module. The 210Rx Module performs the RF reception and decoding. It has 16 available outputs arranged as 4 x 4 easy plug in connectors to interface the one of the output modules.
Output modules 215, 216, 217 provide relay and Triac controlled outputs, any combination of the above modules may be connected to the 210 module to utilise the full 16 outputs. Upto 50 unique transmitter encoders may be learnt to the system. Each of the transmitters may be programmed into individual outputs of the receiver for total control.
See the units below for individual parts and take a look at the data sheet for further details.
Data Sheet
| |
|
|
204 Hand Held Transmitter Ref: 104-115
Pocket Fob with Wall Mounting Holster4, 8/16 Switch Versions Range 433MHz Up to 150 Metres 458MHz NB Up to 500 Metres Miniature enclosure 96 x 47 x 23 Two 3V Lithium Cells (CR2016) LED Indication of Transmission Custom Overlays available A miniature hand held multi channel radio transmitter. Supplied ready to operate. Powered from 2 x lithium cells the 204 transmitter is supplied with either 4 or 8 /16 switches. An LED is provided to show data transmission. The 8/16 unit has 8 switches and a ‘shift’ key, pressing the shift key causes the LED to change from Red to Green shifting the switches as either 1-8 or 9-16. Any transmitter switch may be married to one or many of the receiver’s outputs, or a single switch may be mapped to any number of the receiver’s outputs to enable a powerful and flexible remote control system. Full configuration instructions follow in section 3. The transmitter encoder uses EMC compliant radio transmitter modules and complies with ETSI330-220 When not in use the transmitter sits in the bespoke wall mounting cradle. See options below Delivery B
|  |
|
|
204C4-433F 4 Buttons, 433MHz, 150 metre range Ref: 104-164
Price: £48.00 (Excluding: VAT at 17.5%) | |
|
204C16-433F 9 Buttons (16 Channels), 433MHz, 150 metre range Ref: 104-165
Price: £57.00 (Excluding: VAT at 17.5%) | |
|
204C4-525F 4 Buttons, 434.525MHz, 500 metre range Ref: 104-166
Price: £84.00 (Excluding: VAT at 17.5%) | |
|
204C16-433F 9 Buttons (16 Channels), 434.525MHz, 500 metre range Ref: 104-167
Price: £90.00 (Excluding: VAT at 17.5%) | |
|
207 Hand Held Transmitter Ref: 104-168
4 or 8 Switch Industrial hand held transmitterPolypropylene IP65 Rated Enclosure Range: 433.525MHz Up to 1,000 Metres 458MHz Up to 6,000 Metres Dimensions: 250 x 90 x 45mm (excluding antenna) Low power consumption High Capacity NiMH Rechargeable Battery LED Indication of Transmission and Low Power Auto Transmit mode Auto ‘Watchdog’ Transmission Custom Overlays / Switches available on request Battery Charger Supplied The 207 transmitter is an industrial hand held multi channel radio transmitter. It is supplied in a rugged Polypropylene IP65 rated enclosure. The transmitter features upto 8 robust micro-switch buttons rated upto ten million operations. The 207 has an auto-transmit option link. When this link is enabled the transmitter will send the status of all of its inputs every 5 seconds. This signal is continually monitored by the receiver for reliable operation. See options below Delivery B
|  |
|
|
207C4-525N 4 Buttons, 434.525MHz, 1KM Range Ref: 104-169
Price: £225.00 (Excluding: VAT at 17.5%) | |
|
207C8-525N 8 Buttons, 434.525MHz, 1KM Range Ref: 104-170
Price: £240.00 (Excluding: VAT at 17.5%) | |
|
200/ 201 DIN Rail Transmitters Ref: 104-116
8 Input ChannelsVolt Free contact Inputs via Screw Terminals 12 / 24Vdc Supply Range 433MHz Up to 200 Metres 433MHz NB Up to 1,000 Metres 458MHz Up to 6,000 Metres High Security RF Protocol Auto Transmit Mode Automatic ‘Watchdog’ Transmission Antenna Supplied 201 - Low Power Consumption This is a simple to use 8 channel radio transmitter module which can accept inputs via 8 pairs of ‘Volt free’ screw terminal contacts or two IDC connectors. When a contact closure occurs the transmitter will transmit a data packet over the RF link to an associated 210Rx receiver. (That has been learnt into the Transmitter) The Transmitter module continually monitors the status of its ‘inputs’. Whenever a change of state is seen on any input the module will transmit the status of all inputs. The 201 transmitters have exceptionally low power consumption, allowing for long battery-powered operation. Full configuration instructions are given on the datasheets. The transmitter encoder uses EMC compliant radio transmitter modules and complies with ETSI330-220. see products below Delivery B
|  |
|
|
200-433F 433MHz, 200 metre Range Ref: 104-171
Price: £68.00 (Excluding: VAT at 17.5%) | |
|
200-525N 434.525MHz, 1KM Range Ref: 104-172
Price: £124.00 (Excluding: VAT at 17.5%) | |
|
200-458F 458MHz, 4KM Range Ref: 104-173
Price: £249.00 (Excluding: VAT at 17.5%) | |
|
201-525N 434.525MHz, 1KM Range, Low Power Consumption Ref: 104-174
Price: £125.00 (Excluding: VAT at 17.5%) | |
|
201-458F 458MHz, 4KM Range, Low Power Consumption Ref: 104-175
Price: £258.00 (Excluding: VAT at 17.5%) | |
|
210 Receiver Modules Ref: 104-118
16 Output channelsRange 433MHz Up to 200 Metres 433MHz NB Up to 1,000 Metres 458MHz Up to 6,000 Metres High Security RF Protocol For use with any 200 series transmitter Direct Connection to 200 series Output modules Antenna Supplied This DIN rail module performs the radio reception and decoding for the 200 series modules. It has four output connectors each with four digital outputs and displays the output status on LED’s 1-16. Any of the DIN Rail output modules lug into these connectors marked 1-4 (Connecting cable supplied with output module). NOTE: The 210Rx can only be configured to work with any of the ‘200’ series Transmitters. These include the 200 & 201 DIN Rail mounting transmitter modules and the 204 & 207 portable handheld transmitters. Configuration instructions are given in the transmitter datasheets. See modules below Delivery B
|  |
|
|
210-433F 433MHz, 200 metre Range Ref: 104-176
Price: £48.00 (Excluding: VAT at 17.5%) | |
|
210-525N 434.525MHz, 1KM Range Ref: 104-177
Price: £124.00 (Excluding: VAT at 17.5%) | |
|
210-458F 458MHz, 4KM Range Ref: 104-178
Price: £249.00 (Excluding: VAT at 17.5%) | |
|
Relay Module plug on to the 210 Ref: 104-120
Direct connection to the 210 Receiver Module215: 8 relays rated 230Vac at 3A 216: 4 relays rated 230Vac at 12A (peak) 230: 4 relays rated 230Vac at 30A (peak) Delivery B
|  |
|
|
215 Relay Output Module, 8 Channels, 3A @ 230Vac Ref: 104-179
Price: £35.00 (Excluding: VAT at 17.5%) | |
|
216RL Relay Output Module, 4 Channels, 5A @ 230Vac Ref: 104-180
Price: £36.50 (Excluding: VAT at 17.5%) | |
|
230 Relay Output Module, 4 Channels, 30A @ 230Vac Ref: 104-181
Price: £38.00 (Excluding: VAT at 17.5%) | |
|
211 Screw Terminal Output Module, 16 Channels Ref: 104-182
16 transistor switch outputs Each Output switches to GND when operated Each output rated 500mA at up to 50Vdc Total cumulative output of module 1A at 50Vdc Direct connection to the 210 Receiver Module The 211 DIN Rail module may be connected directly to any of the 210Rx outputs and provides: · 16 transistor switch outputs · Each Output switches to GND when operated · Each output rated 500mA at up to 50Vdc · Total cumulative output of module 1A @50Vdc The only connections required are · Screw terminals to connect to each channel output. · Direct connection to the 210 Receiver via the four ribbon cables / connectors supplied. The module requires no other connections as power is supplied from the 210Rx module Delivery B
Price: £25.50 (Excluding: VAT at 17.5%) |  |
|
|
217T Triac (Dimming) Output Module, 4 Channels, 250W @ 230Vac Ref: 104-183
Direct connection to the 210 Receiver Module4 Output Channels Dimming or Switched Outputs Designed for tungsten filament lamps Supply Voltage: 230Vac Delivery B
Price: £69.00 (Excluding: VAT at 17.5%) |  |
|
|
ENC-DA3 Enclosure for DIN Rail Modules, PSU Fitted Ref: 104-184
IP56 rated protectionInsulation class II Sealable hinged lid screws DIN Rails mounted on steel plate Integrated 12Vdc moulded Power Supply 5 Amp Fused terminal block Cable gland Supplied Accommodates up to 4 x 200 Series DIN Rail Modules Material GW PLAST 120 °C Temperature range: -25 °C to 60 °C The 200 Series DIN rail enclosures are supplied pre-configured with DIN Rails mounted on a metal back plate. A 12Vdc power supply is incorporated. 12Vdc is presented on a fused terminal block. A Gland is supplied to enable power to enter the enclosure. Delivery B
more information
Price: £94.00 (Excluding: VAT at 17.5%) |  |
|
|
Qmax Switching Power Supply Ref: 104-151
Full range AC input High efficiency, low working temperature Built in EMI filter Low ripple & noise Compact size, light weight Short circuit/ Overload protection Installed on DIN rail TS35/7.5 or 15 Approvals: UL/TUV/CE pending Input Voltage 85 - 264V AC, 120 - 370V DC Input Frequency 47 - 63Hz Inrush Current Cold Start, 30A/115V, 60A/230V Overload Protection 105% to 135% output constant current limiting Setup, Rise, Hold up time 800ms, 60ms, 20ms Withstand Voltage I/P-O/P: 3KV, I/P-FG: 1.5KV, 1min. Working Temperature 0º-45ºC@100%, -10ºC@80%, 50ºC@80% Connection 4 P/7.5mm pitch terminal block 4329612 Delivery B
Price: £44.20 (Excluding: VAT at 17.5%) |  |
|
|
X8100 XNET Radio Telemetry Transceiver Ref: 104-136
The unit transmits and receives analogue, digital and pulse counter signals. It is programmed by the user with an individual node address. Each input is then configured to appear as an output on any distant XNET transceiver. It can support up to 128 Digital Inputs, 128 Analogue Inputs, 128 Digital Outputs, 128 Analogue Outputs plus a Serial Gateway for SCADA packages. 458Mhz UK frequency Band Deliver D
data sheet
Price: £498.00 (Excluding: VAT at 17.5%) |  |
|
|
X8104 Analogue Input Module Ref: 104-137
Price: £89.00 (Excluding: VAT at 17.5%) | |
| The module has 4 analogue inputs. Up to 31 Modules can be connected to an X8100 via a 10 way XBUS ribbon cable. For use with X8100 above Delivery tba
|
|
X8105 Analogue Output Module Ref: 104-138
Price: £189.00 (Excluding: VAT at 17.5%) | |
| The module has 4 analogue outputs. Up to 31 Modules can be connected to an X8100 via a 10 way XBUS ribbon cable. For use with X8100 series. Delivery tba
|
|
Colinear Base station Antenna Ref: 104-187
Description: UHF COLINEAR BASE STATION ANTENNA. GRP MAST SUPPLIED WITH A PAIR OF GALVANISED STEEL MASTS SUPPORT BRACKETS ( GLA ) WITH 50 CM RG213 LEAD WITH NTYPE SOCKET FITTED OTHER VERSIONS AVAILABLE VHF: (COLVHF) Frequency: UHF Polarity: VERTICAL Gain: 5db VSWR: 1.5 to 1 Dimensions: Diameter: 25mm GRP MAST Height: CUT TO FREQUENCY Cable: 0.5 metres of RG213 Connector: N TYPE SOCKET WITH SHROUD Power: 50 WATTS Impedance: 50 OHM
Price: £98.00 (Excluding: VAT at 17.5%)
|  |
|
|
End Fed Dipole Base station Antenna Ref: 104-188
END FED UNITY GAIN DIPOLE SUPPLED WITH GALVANISED ANTENNA MAST CLAMPS.GRP MAST .OMNIDIRECTIONAL RADIATION OTHER FREQUENCIES AVAILIBLE LOW BAND (EFDLB) VHF (EFDVHF) UHF (EFDUHF) Frequency: LOW BAND/VHF AND UHF Polarity: VERTICAL Gain: 0db VSWR: 1.5 to 1 Dimensions: Diameter: 25MM Length: 300mm Cable: 0.5 metres of RG213 Connector: N TYPE SOCKET Power: 150 WATTS Impedance: 50 OHM
Price: £60.00 (Excluding: VAT at 17.5%)
|  |
|
|
Lone Worker Alert Ref: 104-112
The Loneworker system is designed for a reliable method for a person to summon assistance when working in a remote location. Simply pressing the red button on the belt transmitter will activate a receiver at a distance of up to 1000m. When the attack button is activated a panic transmission will latch and continue to transmit for 6 seconds ensuring the receiver should respond to the signal. Delivery B
more information
Price: £200.00 (Excluding: VAT at 17.5%) |  |
|
|
RCU-01 Ref: 104-101
The RCU-01 is a radio remote controlled switching unit that will allow the remote operation of any appropriate electrical appliance that is required. The unit is constructed to commercial standards, giving the convenience of remote operation and in most cases the reduction in installation costs will exceed the cost of switching unit. Smart, rigid antenna fixed on the box. Supply voltage range from 10-24V ac or dc. . Dimensions (WxHxD): 75x27x50mm Delivery A
Instruction sheet (PDF)
Price: £35.50 (Excluding: VAT at 17.5%) |  |
|
|
RCU-03 Ref: 104-103
The RCU-03 is a radio remote controlled switching unit that will allow the remote operation of any appropriate electrical appliance that is required. The unit is constructed to commercial standards, giving the convenience of remote operation and in most cases the reduction in installation costs will exceed the cost of switching unit. Supply voltage range from 10-24V ac or dc. Smart, rigid antenna fixed to enclosure. Weatherproof IP65 enclosure. Dimensions (WxHxD): 115x40x65mm Delivery A
Instruction sheet (PDF)
Price: £39.99 (Excluding: VAT at 17.5%) |  |
|
|
RCU-03 (S) Ref: 104-105
The RCU-03 (S) is a radio remote controlled switching unit that will allow the remote operation of any appropriate electrical appliance that is required. The unit is constructed to commercial standards, giving the convenience of remote operation and in most cases the reduction in installation costs will exceed the cost of switching unit. Supply voltage range from 10-24V ac or dc. Smart, rigid antenna fixed to enclosure. Weatherproof IP65 enclosure. This is a special version which gives a 30% increase in distance from transmitter to receiver. Dimensions (WxHxD): 115x40x65mm Delivery A
Instruction sheet (PDF)
Price: £49.99 (Excluding: VAT at 17.5%) | |
|
|
RCU-04 Ref: 104-104
The RCU-04 is a radio remote controlled switching unit that will allow the remote operation of any appropriate electrical appliance that is required. The unit is constructed to commercial standards, giving the convenience of remote operation and in most cases the reduction in installation costs will exceed the cost of switching unit. Supply voltage range from 220- 240V ac. Smart, rigid antenna fixed to enclosure. Weatherproof IP65 enclosure. Dimensions (WxHxD): 115x40x65mm Delivery A
Instruction sheet (PDF)
Price: £39.99 (Excluding: VAT at 17.5%) |  |
|
|
RCU-04 (S) Ref: 104-107
The RCU-04 (S) is a radio remote controlled switching unit that will allow the remote operation of any appropriate electrical appliance that is required. The unit is constructed to commercial standards, giving the convenience of remote operation and in most cases the reduction in installation costs will exceed the cost of switching unit. Supply voltage range from 220- 240V ac. Smart, rigid antenna fixed to enclosure. Weatherproof IP65 enclosure.This is a special unit which give a range 30% greater than the normal 04 version. Dimensions (WxHxD): 115x40x65mm Delivery A
Instruction sheet (PDF)
Price: £49.99 (Excluding: VAT at 17.5%) | |
|
|
RCU keyfob Ref: 104-106
A two button key fob transmitter that contains replaceable batteries. This is used in the RCU series of units and is sold as an addon. Delivery A
Price: £16.95 (Excluding: VAT at 17.5%) |  |
|
|
TX7120 Low Cost, Rugged Telemetry Transmitter Ref: 104-111
The unit has 4 digital inputs, 1 analogue input and a pulse counter. An LCD display is used to display the current analogue and digital data along with a set up menu.A simple back to back link can be implemented using a RX7120 receiver. A group of TX7120 can configured to a single RX7100 Telemetry Receiver. This unit is a 500mW Transmitter.
Price: (5 or fewer items) £359.00 (Excluding: VAT at 17.5%)
Price: (6 to 49 items) £303.00 (Excluding: VAT at 17.5%)
Price: (50 or more items) £287.00 (Excluding: VAT at 17.5%)
|  |
|
|
RX7120 Low Cost Rugged Radio Telemetry Receiver Ref: 104-113
The unit has 4 relay outputs, 1 analogue output, 1 serial output and a link fail relay output. The received data is displayed on a LCD display.The RX7120 can be used in conjunction with either a TX7120 , TX7121, TX7100 or X7100 Radio Telemetry Transmitter.
Price: (5 or fewer items) £366.00 (Excluding: VAT at 17.5%)
Price: (6 to 49 items) £281.00 (Excluding: VAT at 17.5%)
Price: (50 or more items) £267.00 (Excluding: VAT at 17.5%)
|  |
|
